TRAVELSCOOT Kit bagages intelligent
149,00 €
En stock ✓, test possible en boutique 🗸, délai de livraison:
- pour expédition ...⛟ : 2-5 jours ouvrables
- en cas de retrait en magasin : directe 🗸
Réf. produit :
13927.1
Informations sur le produit "TRAVELSCOOT Kit bagages intelligent"
Kit porte-bagages pour fixer un maximum de bagages sur le TRAVELSCOOT Escape & Shopping Cruiser
Se compose de :
Rail adaptateur (pour recevoir la plateforme de rangement à l'avant)
Plate-forme de rangement (profilé en forme de L pour recevoir les bagages à l'avant)
Pièce en plastique en forme d'oméga (stabilise les bagages à l'avant sur la colonne de direction)
Dispositif de traction pour valises à roulettes (pour fixer les valises à roulettes à l'arrière - dossier)
Systèmes de sangles pour l'arrimage des bagages
Les valises et les sacs de voyage illustrés ne font pas partie du kit !
Se compose de :
Rail adaptateur (pour recevoir la plateforme de rangement à l'avant)
Plate-forme de rangement (profilé en forme de L pour recevoir les bagages à l'avant)
Pièce en plastique en forme d'oméga (stabilise les bagages à l'avant sur la colonne de direction)
Dispositif de traction pour valises à roulettes (pour fixer les valises à roulettes à l'arrière - dossier)
Systèmes de sangles pour l'arrimage des bagages
Les valises et les sacs de voyage illustrés ne font pas partie du kit !
| ••• SOUS-CATÉGORIES •••: | ACCESSOIRES DE VOYAGE |
|---|
| Fabricant "TRAVELSCOOT"
TravelScoot Hartmut Huber
Grovestrasse 2
D-80997 München
E-Mail: international@travelscoot.com
Question : Hi, What parts are included in support platform front?
From : customer
Answer:
Dear, all parts except the hook for the luggage on the rear - back rest.
1) Remove part (see arrow)
S
2) Insert the adapter rail (B) into the U-shaped basket
holder so that the smooth side is at the back.
B,
N
The two small screws act as locking pins.
The two small screws act as locking pins and are inserted into the holes
m 74
3) Slightly loosen the round-head screws and remove the
the angled storage platform (A) with the keyhole
with the keyhole openings over the screw heads and
and lower it into the slot. Tighten the screws
tighten the screws.
4) Snap the omega-shaped plastic part (spacer holder) (C)
over the steering column and attach the aluminium tube strip (C)
to it with the Velcro surfaces.
5) Attach the two short straps (D) to the case handle.
6) Attach the longer strap (E) with the Velcro surfaces to the
Traveiscots on the handle. the spacer holder =
(©) and strap (E) and stow them in your hand luggage.
7) Move the TravelScoot handlebars to the top position and
lock the lifting clamp.
Place the suitcase on the storage platform (A) and secure it with the short straps
the short straps (D) around the top of the steering column so that the suitcase
firmly against the spacer (C). The cables leading to the
to the control elements must be free and the handlebars must
remain rotatable. If this is not possible, the case does not comply with
the IATA dimensions.
Hold the belt over the case from below and tighten the belt clamp.
tighten. .
8) screw the rolling suitcase pulling device (F) onto the backrest holder
as far down as possible,
'
9) Hang up the wheeled suitcase.
After sitting on the seat
another piece of luggage
under the seat
)
Shopping br
10) Loop the straps (6) into the handles of the crate
and mark the top edge of the box in the centre. -p
8 17) Lift the crate onto the storage platform (A) so that the
mark with the control column, loop the straps (G) around the Omega
around the Omega spacer (C) and fasten,
Tighten the belt tensioners firmly. The two strong luggage
17] Attach the two strong rubber straps (H) to the box and to the cane/crutch holder.
and on the cane/crutch holder. These act as tilt dampers.
>
'Attention: A crate as in step
11.) can be filled with approx. 20
kilos, but care must be taken with regard to weight.
However, care must be taken with regard to the weight. As the Travelscoot
itself only weighs 16 kilos, there is a risk that the entire loaded structure will fall over the
loaded structure could tip over the front wheel. For this reason, additional containers should be carried on the rear TravelScoot
frame and these should be filled first as a counterweight.
be filled first.
Important: If the loaded crate is to be removed, it must be held and lifted by a second person.
be held and lifted by a second person before the belt buckle is opened and the luggage
the rubber straps (H) are removed
12) Extra belt (} for any use ee
== Sams
ÜravelScoot’
Translated with www.DeepL.com/Translator (free version)
Question : kann man mit dem System vorne, auch breitere Kisten von ca 50 cm, montieren. LG Lenk
From : customer
Answer:
Hallo Frau Lenk,
theoretisch ja, aber die Stabilität ist dann nicht mehr sehr gut wenn schwere Sachen seitlich in der Kiste liegen.
Also es kommt eher auf die Anwendung an. Mit freundlichen Grüßen
TravelScoot sales EU
